DIY Iron On Nautical Bachelorette Tank Tops

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

Whats better for a cruise bachelorette party than matching bridal party tank tops? :) I adored this design so much on tote bags I had to use it for tank tops as well and it looked great either way!

These are just as easy as their tote bag counter parts, and I adore the white and silver popping on darker, colorful tank tops! :)

Supplies:
Blank Tank Tops
Easyweed Heat Transfer Vinyl or Glitter Heat Transfer Vinyl
Craft Cutter and Tool Set
Adhesive Mat
Tank Top Design Cut Files

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the tank tops the way you like.

2. After selecting “Make It” Make sure to select the Mirror Mode on the cutting screen. Cut the design(s) in your choice of heat transfer vinyl (I used Silver Glitter HTV and White HTV) with the Iron On (for Easyweed Vinyl) or Iron On+ (for Glitter Vinyl) Setting on your Cricut, with the shiny side of the material down.

3. Weed the additional material off of the backing material so that, looking down with the shiny side up, you can see your design with the correct orientation.

4. Iron your tank top to remove any creases, then center the design over the top half of the tank top. Arrange the design shiny side up, then cover with parchment paper. Make sure to keep the parchment paper between the design and the iron.

5. Set your Iron to the second Highest setting and press the the iron down firmly on the design, not ironing but rather using it as a small heat press. I worked from the upper left to lower right on the design, pressing the iron on each part of the design for at least 30 seconds, then overlapping the last position as you move the iron across the design.

6. Remove the backing from the design, leaving the design on the tank top. Repeat with all the remaining tank tops.

Nothing like matching tank tops to keep all your brides-mates accounted for and ready to party! What designs would you make for bachelorette tank tops? :)

Feeling Nauti Bridesmaid Flasks

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

To go with our Feeling Nauti Tote Bags, I decided to also design a set of flasks along the same theme. After all, what better accessory for a bachelorette beach bag than a matching flask? :)

The big thing with these designs is to be careful wedding the bride’s “Shipfaced” flask, the words and outline are easy but the little details in the steering wheel can be a little tougher depending on how comfortable you are weeding vinyl. I didn’t need an extra, but since they don’t take that much vinyl to make I would recommend cutting an extra just in case. :)

Supplies:
Flasks
Permanent Adhesive Vinyl
Transfer Paper
Craft Cutter and Toolset
Flask Design Cut File

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. 

2. Cut the design(s) in your choice of permanent adhesive vinyl with the Vinyl Setting on your Cricut. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so.

3. Once the designs are cut, weed away the extra vinyl and cut a piece of transfer taper to 3.5" x 5". I found that the Cricut transfer tape was easiest for this since its grid lines are in 1/2” segments. Cut away any excess backing from the vinyl design and smooth transfer tape over the design, aligning it along the bottom of the top word (“Feeling” or “Ship”) 1 1/2” from the top of your transfer tape (3 blocks down if you are using Cricut Transfer tape). Using the smoother tool, smooth the tape to the vinyl, removing any air bubbles. The transfer tape should overlap the backing of the design, so that you can stick the tape to an object with the backing still on the design.

4. Now, transfer the design to your flask. If you are comfortable centering the designs you can remove the tape from the backing and directly place the design on the flask. If not, arrange the design to be centered on the flask before removing the backing, sticking it with the overlapping transfer tape.

5. Once your design is placed to your satisfaction, carefully peel the tape off the backing, transferring the vinyl to the transfer tape while not unsticking it from the flask. Remove the backing then smooth the design onto the flask, once again using the smoother to remove any air bubbles. I found it pretty easy to simply lift the design and transfer directly, as shown in teh photos below. Since the designs are not symmetrical, I simply aligned it to the center “block” of the transfer tape then made sure that the top of the transfer tape followed the top of the flask, as shown below.

6. Remove the transfer taper to leave the design on the flask, then repeat the process for all the additional flasks.

And now you have some cute and nautical bachelorette flasks for your favorite girls to help celebrate! :)

DIY Nautical Bachelorette Iron On Canvas Tote Bags

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

Who loves cruises for Bachelor and Bachelorette Parties? I know I do! I’ve had the fun of helping with one cruise ship wedding but I like it even more for bachelorette parties! To get in the spirit (and because I knew my husband will soon be attending a cruise bachelor party) these tote bags were born!

These totes are surprisingly easy considering that the design is both large and more complex but just like the other files on this blog, the entire design can be easily downloaded all at once into your Cricut software, just make sure to cut out your design mirrored, with your HTV shiny side down! :)

Supplies:
Blank Tank Tops
Easyweed Heat Transfer Vinyl or Glitter Heat Transfer Vinyl
Craft Cutter and Tool Set
Adhesive Mat
Tote Bag Design Cut Files

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the tank tops the way you like.

2. After selecting “Make It” Make sure to select the Mirror Mode on the cutting screen. Cut the design(s) in your choice of heat transfer vinyl with the Iron On (for Easyweed Vinyl) or Iron On+ (for Glitter Vinyl) Setting on your Cricut, with the shiny side of the material down.

3. Weed the additional material off of the backing material so that, looking down with the shiny side up, you can see your design with the correct orientation.

4. Iron your tank top to remove any creases, then center the design over the top half of the tank top. Arrange the design shiny side up, then cover with parchment paper. Make sure to keep the parchment paper between the design and the iron.

5. Set your Iron to the second Highest setting and press the the iron down firmly on the design, not ironing but rather using it as a small heat press. I worked from the upper left to lower right on the design, pressing the iron on each part of the design for at least 30 seconds, then overlapping the last position as you move the iron across the design.

6. Remove the backing from the design, leaving the design on the Tote Bag. Repeat with all the remaining totes.

I absolutely adore how these came out and they were so easy to make! I can’t wait to try this design on tank tops and see how it turns out! :)

Modern Wine Bottle Table Numbers

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

We are back for another take on Wine Bottle Table Numbers! I love wine bottle for centerpieces and having the table number on the bottle is a fun detail and a cheap way to make table numbers in general. I’ve made a couple before this and I own that there will likely be more in the future, there are so many possibilities! :)

These designs I wanted to look similar to an actual wine bottle label as far as size, with the number cut out, but as it turns out I really liked them either way. By weeding out the numbers or removing the “label” part, you can have just the Table and number in vinyl or you can choose to remove the Text and numbers, making a more label-esque choice. These two choices could easily be alternated between or you can pick your favorite of the two!

Supplies:
Empty Wine Bottles
Permanent Adhesive Vinyl
Transfer Tape
Craft Cutter and Tool Set
Adhesive Mat
Table Number Design Cut Files

1. First, soak your wine bottles in hot, soapy water to remove the labels and adhesive. I found it easiest to soak them for about 5 minutes, remove what l could, then once the label was completely removed clean up the last bits of adhesive with steel wool. :)

2. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save.  

3. Cut the design(s) in your choice of permanent adhesive vinyl with the Vinyl Setting on your Cricut. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the wine bottles the way you like.

4. Once the designs are cut, weed away the extra vinyl and cut a piece of transfer taper to 3.5" x 5". You can weed these table numbers in two ways, either by weeding the numbers and text, leaving a rectangle with the Table number weeded, or by removing the rectangle, leaving the Table number in vinyl.

5. Cut away any excess backing and smooth transfer tape over the design. I aligned the rectangle table number along the gridelines of the transfer tape and for the numbers only style, I aligned the tape along the “T” and top of the number, as shown below. Using the smoother tool, smooth the tape to the vinyl, removing any air bubbles. The transfer tape should overlap the backing of the design, so that you can stick the tape to an object with the backing still on the design.

6. Now, transfer the design to your bottle. If you are comfortable centering the designs you can remove the tape from the backing and directly place the design on the wine bottle. If not, arrange the design to the bottle before removing the backing, sticking it with the overlapping transfer tape.  I aligned mine to the bottom of the wine bottles, as shown in the photos below. I didn’t have much issue transferring the designs directly, but it never hurts to keep on the backing while you arrange it if you are nervous! :)

6. Once your design is placed to your satisfaction, transfer the design to the bottle. If you kept on your backing, carefully peel the tape off the backing, transferring the vinyl to the transfer tape while not unsticking it from the bottle. Remove the backing then smooth the design onto the bottle. If you didn’t use the backing, smooth design onto the bottle, using your fingers to remove air bubbles.

7. Remove the transfer tape to leave the design on the wine bottle, then repeat the process for all your additional table numbers.

DIY Iron On Bachelorette Drinking Team Tank Tops

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

I’m always a fan of everyone having matching tank tops for bachelorette parties; it is such a nice way for everyone to be a part of the group and makes for wonderful pictures to commemorate all the fun! If you are worried that its too hard to make your own, enter these Bachelorette Drinking Team Tank Tops!

I wanted to start more simple with my first set of bachelorette tank tops, and I love how they came out! I highly recommend Glitter Heat Transfer Vinyl for these, they came out stunning! :) And just like our other tutorials, these svg files are designed so that it is as easy as upload, cut, iron, done! :)

Supplies:
Blank Tank Tops
Easyweed Heat Transfer Vinyl or Glitter Heat Transfer Vinyl
Craft Cutter and Tool Set
Adhesive Mat
Tank Top Design Cut Files

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the tank tops the way you like.

2. After selecting “Make It” Make sure to select the Mirror Mode on the cutting screen. Cut the design(s) in your choice of heat transfer vinyl (I used Gold Confetti Glitter HTV) with the Iron On (for Easyweed Vinyl) or Iron On+ (for Glitter Vinyl) Setting on your Cricut, with the shiny side of the material down.

3. Weed the additional material off of the backing material so that, looking down with the shiny side up, you can see your design with the correct orientation.

4. Iron your tank top to remove any creases, then center the design over the top half of the tank top. Arrange the design shiny side up, then cover with parchment paper. Make sure to keep the parchment paper between the design and the iron.

5. Set your Iron to the second Highest setting and press the the iron down firmly on the design, not ironing but rather using it as a small heat press. I worked from the upper left to lower right on the design, pressing the iron on each part of the design for at least 30 seconds, then overlapping the last position as you move the iron across the design.

6. Remove the backing from the design, leaving the design on the tank top. Repeat with all the remaining tank tops.

These tank tops are a beautiful and affordable option for a bar crawl bachelorette! What other Bachelorette tank tops would you like to see? :)

Monogram Canvas Tote Bags

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

If there is one thing I adore on Etsy its all the monogrammed swag you can buy for yourself and your maids for your wedding! I love monogrammed items, but have always been nervous to try it myself because I assumed it would be difficult. Luckily, that was not the case! :)

I ended up finding a free monogram font (that I reference below) and it took all of 15 minutes of playing around with the software for my Cricut to easily make oodles of monograms, so I started with tote bags! Tote bags, especially canvas ones like these, are great for your wedding party for a beach or destination wedding where your maids will want a beach bag to throw their things in. :)

In this tutorial, I’ll go step by step to show you how to make monograms in your Cricut software for tote bags of your own or whatever else you want to monogram! :)

Supplies:
Blank Tote Bags
Easyweed Heat Transfer Vinyl or Glitter Heat Transfer Vinyl
Craft Cutter and Tool set
Adhesive Mat
Iron and Ironing Mat

Designing Your Monogram:

1. First, if you don't already own a Monogram style font, download one. The font I used is called Free Monogram Font from DaFont.com and it worked perfectly for what I wanted, and as the name implies its totally free!

2. Now, open a new project in your Cricut design software and create a text box. Select the Monogram font from your font choices and use it to type the initials for your monogram.

3. If you are using the font I mentioned, for smaller side letters you use lower case letters and for the center letter you use uppercase letters. For example, my initials on the monogram shown are typed in as "aCl" .

4. Next, overlap your letters by changing the letter spacing of your font. I chose -2 for the spacing of my letters but it is better to mess with it a little bit to find out what looks best to you.

5. Once all your letters are spaced to your satisfaction, select the "Weld" tool to combine your letters into a single set of cutting curves. 

6. Now,  you can size your monogram to whatever size you like best. For the small monograms, I made them 3" wide and for the large monograms, I made them 10.5" wide.

7. Finally, cut the monograms on your choice of vinyl. I used the Iron On+ setting for Glitter HTV and the Standard Iron On Setting for regular Easyweed Vinyl. Make sure that you select the "Mirror" Function and load your Iron On material Shiny side down so that your design cuts correctly! :)

Transferring your Design

8. Once your design is cut, weed away the extra material, leaving only your monogram.

9. Iron your Tote Bag to remove any creases, then arrange the Monogram where you want to transfer it on your tote. For large monograms I put it in the middle and for smaller monograms I preferred the lower right corner. Arrange the design shiny side up, then cover with parchment paper. Make sure to keep the parchment paper between the design and the iron.

10. Set your Iron to the second Highest setting and press the the iron down firmly on the design, not ironing but rather using it as a small heat press. I worked from the upper left to lower right on the design, pressing the iron on each part of the design for at least 30 seconds, then overlapping the last position as you move the iron across the design.

11. Remove the backing from the design, leaving the Monogram on the Tote Bag. Repeat with all the remaining Totes.

I was very pleasantly surprised with how easy these were to make and now have several other monogram projects in the wings to show bunches of different monogrammed projects! :) What are your favorite monogrammed items?

Wreath Wine Bottle Table Numbers

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

Wine bottle centerpieces are always a cost effective choice for the wine loving bride with bottles to spare, so I decided to spruce up the table numbers for such a centerpiece with some vinyl decals. They can be put on the bottles beforehand to designate your wedding tables and are a super easy project for your Cricut, literally load, cut, weed and stick.

While I’ve made Wine Bottle Table numbers before, I couldn’t help thinking of some other design ideas over the last several months and so I decided to return to them and make a couple options so that you can better personalize your wine bottle centerpieces depending on your style. This first set is a fairly simply script set surrounded by a simple vine and leaf “wreath,” perfect for most wedding with natural elements.

You will notice in the cut file downloads that there are both full sheets for groups of the table numbers and individual table numbers. Both types of files will be the same size of table number when cut so you can use either interchangeably. It is worth noting that, since the circling vine is thin, sometimes weeding these designs require a little care and extra attention. I did not have to redo any, but in case you have a problem, you can easily upload the single table number file to replace any table number casualties.

Supplies:
Empty Wine Bottles
Permanent Adhesive Vinyl
Transfer Tape
Craft Cutter and Tool Set
Adhesive Mat
Table Number Design Cut Files

1. First, soak your wine bottles in hot, soapy water to remove the labels and adhesive. I found it easiest to soak them for about 5 minutes, remove what l could, then once the label was completely removed clean up the last bits of adhesive with steel wool. :)

2. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save.  

3. Cut the design(s) in your choice of permanent adhesive vinyl with the Vinyl Setting on your Cricut. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the wine bottles the way you like.

4. Once the designs are cut, weed away the extra vinyl and cut a piece of transfer taper to 4" x 4.5". Cut away any excess backing and smooth transfer tape over the design, aligning it so that “Table” is aligned to the transfer tape grid 2” from the top of the transfer tape (4 blocks down if you are using the Cricut 1/2” transfer tape), as shown below. Using the smoother tool, smooth the tape to the vinyl, removing any air bubbles. The transfer tape should overlap the backing of the design, so that you can stick the tape to an object with the backing still on the design.

5. Now, transfer the design to your bottle. If you are comfortable centering the designs you can remove the tape from the backing and directly place the design on the wine bottle. If not, arrange the design to the bottle before removing the backing, sticking it with the overlapping transfer tape.  I aligned mine without the backing by lining up the bottom of the transfer tape with the bottom of the bottle without much trouble, as shown in the photos below. Smooth design onto the bottle, removing any air bubbles.

6. Remove the transfer tape to leave the design on the wine bottle, then repeat the process for all your additional table numbers.

This is a project that is super easy to do months in advance and the bottles can be easily stored together and set up the day of your wedding. :) Pick your favorite bottles to make into table numbers then simply gather other bottles and candles around them for a pretty and cheap centerpiece!

Soon to be Drunk Bachelorette Flasks

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

I love designing flasks for bachelorette parties, they are the perfect accessory for any group out on the town! Since I already had flasks from my previous projects, I decided to keep designing for them! :)

These flasks are a simple, cute design for any bar crawl or bachelorette party where booze is to be ingested (so pretty much all of them). Be careful when you are weeding the “Drunk” and “Mrs” middle bits, sometime they are a bit tricky.

Supplies:
Flasks
Permanent Adhesive Vinyl
Transfer Paper
Craft Cutter and Tool Set
Adhesive Mat
Flask Design Cut File

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. 

2. Cut the design(s) in your choice of permanent adhesive vinyl with the Vinyl Setting on your Cricut. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so.

3. Once the designs are cut, weed away the extra vinyl and cut a piece of transfer taper to 4" x 5". Cut away any excess backing from the vinyl design and smooth transfer tape over the design, aligning it to the “Soon” on each decal as shown below. Using the smoother tool, smooth the tape to the vinyl, removing any air bubbles.

4. Now, transfer the design to your flask. I arranged mine by the bottom of the transfer tape following the bottom of the flask with the design centered by placing the opening of the flask between the two “O’s” of the “Soon.”

5. Once your design is placed to your satisfaction, smooth the design onto the flask, once again using the smoother to remove any air bubbles.

6. Remove the transfer tape to leave the design on the flask, then repeat the process for all the additional flasks.

Just like the other flasks I’ve made, these were super simple and came out great! :) There will be plenty of future flasks, so check them out here!

DIY Bride Tribe Iron On Tank Tops

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

These are the first bridal party tank tops I’ve designed and I love how then turned out! :) They can be easily given as bridesmaid invitations, bachelorette tank tops or even getting ready tank tops! I adore this design and it would work equally well on tote bags or tshirts.

While I’ve worked a good amount with adhesive vinyl, this was the first time I worked with HTV, and I was very nervous! Luckily there wasn’t much to be worried about. :) Other than making sure the design gets mirrored (which you do before cutting) the only other question was how to best “iron it on.” As it turns out, the best way is to use your iron as a mini heat press, pressing it to part of the design, then lifting it and pressing the next piece, until the design has all been heat pressed.

Supplies:
Blank Tank Tops
Easyweed Heat Transfer Vinyl or Glitter Heat Transfer Vinyl
Craft Cutter and Tool Set
Adhesive Mat
Parchment Paper
Tank Top Design Cut Files

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the tank tops the way you like.

2. After selecting “Make It” Make sure to select the Mirror Mode on the cutting screen. Cut the design(s) in your choice of heat transfer vinyl (I used Gold Confetti Glitter HTV) with the Iron On (for Easyweed Vinyl) or Iron On+ (for Glitter Vinyl) Setting on your Cricut, with the shiny side of the material down.

3. Weed the additional material off of the backing material so that, looking down with the shiny side up, you can see your design with the correct orientation.

4. Iron your tank top to remove any creases, then center the design over the top half of the tank top. Arrange the design shiny side up, then cover with parchment paper. Make sure to keep the parchment paper between the design and the iron.

5. Set your Iron to the second Highest setting and press the the iron down firmly on the design, not ironing but rather using it as a small heat press. I worked from the upper left to lower right on the design, pressing the iron on each part of the design for at least 30 seconds, then overlapping the last position as you move the iron across the design.

6. Remove the backing from the design, leaving the design on the tank top. Repeat with all the remaining tank tops.

DIY Heart Bridesmaid Flasks

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

With all the fun I had making the Groomsman Mustache Flasks, I couldn't leave the Bridesmaids out of the shinanigans! These Heart flasks are a simple and understated way to invite your bridesmaids to your wedding party or to use as a bachelorette favor or wedding gift! And of course I included one for the Bride so that all the wedding ladies can celebrate together!

The only difficult part of this project is to make sure some of the smaller pieces of vinyl don't get removed while weeding the letters from the heart (like the middle of the "e's" and "d's") so take your time on weeding the design and cut a couple extras if you are nervous! :)

Supplies:
Flasks
Permanent Adhesive Vinyl
Transfer Paper
Craft Cutter and Tool Set
Adhesive Mat
Flask Design Cut File

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save.  

2. Cut the design(s) in your choice of permanent adhesive vinyl with the Vinyl Setting on your Cricut. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the flask the way you like.

3. Once the designs are cut, weed away the extra vinyl and cut a piece of transfer taper to 4" x 3.5". I recommend using a transfer tape with 1/2" gridlines such as the Cricut brand tape as it makes it much easier to precisely transfer to the flasks. Cut away any excess backing and smooth transfer tape over the design, aligning it so that the  middle on the long side of your transfer tape is centered along the middle of the heart, with the bottom of the heart at the bottom of the transfer tape, as shown below. Using the smoother tool, smooth the tape to the vinyl, removing any air bubbles. The transfer tape should overlap the backing of the design, so that you can stick the tape to an object with the backing still on the design.

4. Now, transfer the design to your flask. If you are comfortable centering the designs you can remove the tape from the backing and directly place the design on the flask. If not, arrange the design to be centered on the flask before removing the backing, sticking it with the overlapping transfer tape.  I aligned mine such that the middle of each heart was centered on the top cap of the flask and the top of the transfer tape ran along the top edge of the flask, as shown in the photos below.

5. Once your design is placed to your satisfaction, carefully peel the tape off the backing, transferring the vinyl to the transfer tape while not unsticking it from the flask. Remove the backing then smooth the design onto the flask, once again using the smoother to remove any air bubbles.

6. Remove the transfer taper to leave the design on the flask, then repeat the process for all the additional flasks.

DIY Groomsman Mustache Flasks

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

Whether they are used as Groomsman Proposals, Bachleor Party Favors, or even Groomsman Gifts, giving flasks to Groomsmen is always a fun gift for them to recieve! I remembered a set I saw once on Pinterest that were a collection of mustaches and was determined to make a set for myself!

I absolutely love the way they turned out and all the different styles of mustaches that I designed! Below you can find the cut files for all the different flasks as well a one for the Groom so he isn't left out of the fun! :) Each file can be uploaded individually so you can either have all your groomsmen flasks match with the same 'stache or pick which one you think fits each of your boys best!

Supplies:
Flasks
Permanent Adhesive Vinyl
Transfer Paper
Craft Cutter and Tool Set
Adhesive Mat
Flask Design Cut File

1. After downloading the cut files, import them into the Cricut Software. After creating a new project, select Upload Image. Select the file you wish to upload and it will automatically take you to the final upload screen, where you can name the file the select Save. 

2. Cut the design(s) in your choice of permanent adhesive vinyl with the Vinyl Setting on your Cricut. The SVG Files are sized so that they will automatically cut to the size you see in the photos, but if you want to change the size you can do so to fit the flask the way you like.

3. Once the designs are cut, weed away the extra vinyl and cut a piece of transfer tape to 4" x 5". I recommend using a transfer tape with 1/2" gridlines such as the Cricut brand tape as it makes it much easier to precisely transfer to the flasks. Cut away any excess backing and smooth transfer tape over the design, aligning it along the bottom of the Groomsman text, with one row of the 1/2" blocks below it. I also tried to align mine with one of the vertical lines centering in the middle of the mustache, but it is more important to get the text straight. :) Using the smoother tool, smooth the tape to the vinyl, removing any air bubbles. The transfer tape should overlap the backing of the design, so that you can stick the tape to an object with the backing still on the design.

4. Now, transfer the design to your flask. If you are comfortable centering the designs you can remove the tape from the backing and directly place the design on the flask. If not, arrange the design to be centered on the flask before removing the backing, sticking it with the overlapping transfer tape. I aligned mine such that the middle of each mustache was centered on the top cap of the flask and the top of the transfer tape ran along the top edge of teh flask, as shown in the photos below.

5. Once your design is placed to your satisfaction, carefully peel the tape off the backing, transferring the vinyl to the transfer tape while not unsticking it from the flask. Remove the backing then smooth the design onto the flask, once again using the smoother to remove any air bubbles.

6. Remove the transfer taper to leave the design on the flask, then repeat the process for all the additional flasks.

Once they are all completed, they can be easily wrapped back up in their original boxes or paired with a card or your Groomsmen's spirit of choice! :)

DIY Groomsman Humidors

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

I absolutely love the idea of giving humidors as Groomsman Gifts or even as Groomsman Proposals if you have the budget for it! When I was getting married, I ended up hand etching all of my boys' humidors with their names and a mountain range, but vinyl is a far quicker way to create a beautiful gift for all your groom's best guys for your wedding day.

For these groomsman and best man humidors, I went with a simple bow tie design to leave plenty of space for viewing cigars, but if you want to have extra personalization on your humidors, you can add it on the bottom (the font I used is called Antonio).

Supplies:
Glass Top Humidors
Permanent Adhesive Vinyl
Craft Cutter and Tool Set
Adhesive Mat
Transfer Tape
Groomsman Cut File
Best Man Cut File

1. Download the Groomsman and Best Man Cut Files by clicking the links above, which will open the file into a new tab. right click on the picture and select "Save Picture as".  

2. Import the files into the Cricut software. You can do this by going to the software; and, after making a new project, click the "Upload Button." Then Select Upload Image

3. Click "Browse" and select the file you want to cut from your saved files. Once the file is selected, a new screen will appear to choose cut complexity. I generally find the best results on the "Moderately Complex" Setting. Click your setting of choice then click "Continue."

4. You will now be on the "Select and Erase Screen." In this case, there is nothing to erase so just press continue to go to the final screen. Here you can choose whether is is a "Print to cut" file or regular "Cut" File. Select the Cut file, then press "Save."

5. Back on the Upload Screen, Repeat Steps 1 - 4 on the "Best Man" image. Once both images have been uploaded, select them from the main "Upload Screen" and click "Insert Images."

6. Both the "Groomsman" and "Best Man" Decals should be on your Project Screen. Size both decals to be 6.25" wide to have them be a similar size to the humidors pictured. Then copy and paste additional decals as needed from these resized ones. Press "Make It" to go to the Cut Screen.

7. On the Prepare Screen, confirm that your designs are arranged as you would like them on the cutting mat, then press "Continue." You can move any object by dragging and dropping it on the mat. Finally, load your vinyl of choice, select "Vinyl" on your machine, load your craft cutter, then press the Cricut "C" button on the cutter when it blinks.

8. Cut out your files on the adhesive vinyl of your choice and weed the extra vinyl from the design.

9. Press transfer tape along the design, aligning the text with the grid lines of the transfer tape. Use a smoother tool to release any air bubbles and the get the vinyl to stick to the tape.

10. If you aren't comfortable eyeballing the placement of your design, take an extra piece of transfer tape and adhere it to the inside of the humidor glass, starting at the top edge of the lid. Now, all the grid lines will be parallel to the window frame of the humidor,.

11. Slowly remove the tape from the vinyl design, making sure that the design transfers from the vinyl backing to the tape.

12.  From the middle of the glass, smooth the design with a smoother to remove any air bubbles. Once design has been pressed onto the glass, slowly remove the transfer tape, confirming that the design transfers from the tape to the glass. Repeat with all your remaining humidors.

13. Remove the transfer tape from the inside of the humidor, then repeat the process for the rest of your humidors! :)

DIY Bridesmaid Wine Glasses

This post contains affiliate links, meaning that if you click on a link I will recieve a small comission. This costs you nothing extra and I only promote products I use and love! You can read our full disclosure here

One of my favorite things to make for bridal parties are themed glasses, whether for DIY Nights, Bachelorette Parties, Bridal Showers, or Getting ready on the big day! I will be posting on how to make your own personalized glasses in a bit, but these are more generic and can be easily used for all wedding events by your girls. 

I cut out mine using a Champagne Glitter Vinyl, but there are many options to choose from if it's not quite right for wedding party. Also worth noting, when I designed the cut files I kept the text black on a blank canvas, so on my computer then tend to be on a black background and can't be seen very well, you can right click to either copy the file or save it and it should be black text with a clear background. :)

Supplies:
Stemless Wine Glasses
Permanent Adhesive Vinyl
Craft Cutter and Tool Set
Adhesive Mat
Transfer Tape
Bridesmaid Cut File
Maid of Honor Cut File

1. Download the Bridesmaid and Maid of Honor Cut File by clicking the links above, which will open the file into a new tab. right click on the picture and select "Save Picture as".  

2. Import the files into the Cricut software. You can do this by going to the software; and, after making a new project, click the "Upload Button." Then Select Upload Image

3. Click "Browse" and select the file you want to cut from your saved files. Once the file is selected, a new screen will appear to choose cut complexity. I generally find the best results on the "Moderately Complex" Setting. Click your setting of choice then click "Continue."

4. You will now be on the "Select and Erase Screen." In this case, there is nothing to erase so just press continue to go to the final screen. Here you can choose whether is is a "Print to cut" file or regular "Cut" File. Select the Cut file, then press "Save."

5. Back on the Upload Screen, Repeat Steps 1 - 4 on the "Maid of Honor" image. Once both images have been uploaded, select them from the main "Upload Screen" and click "Insert Images."

6. Both the "Bridesmaid" and "Maid of Honor" Decals should be on your Project Screen. Size your "Bridesmaid" Image to 4.5" wide and the "Maid of Honor" image to 3" tall to have them be a similar size to the glasses pictured. Then copy and paste additional decals as needed from these resizes ones. Press Continue to go to the Cut Screen.

7. On the Prepare Screen, confirm that your designs are arranged as you would like them on the cutting mat, then press "Continue." You can move any object by dragging and dropping it on the mat. Finally, load your vinyl of choice, select "Vinyl" on your machine, load your craft cutter, then press the Cricut "C" button on the cutter when it blinks.

8. Cut out your files on the adhesive vinyl of your choice and weed the extra vinyl from the design.

9. Press transfer tape along the design, aligning the text with the grid lines of the transfer tape. Use a smoother tool to release any air bubbles and the get the vinyl to stick to the tape.

10. Slowly remove the tape from the vinyl design, making sure that the design transfers from the vinyl backing to the tape.

11. Angle your text such that it leaves about an inch around the top of the glass and stick the middle of the design on the wine glass. From the middle of the glass, smooth the design along the curve of the glass from the middle to the edges. The transfer tape won't perfectly lay on the glass due to its curved surface, but the text can be smoothed on without much fuss.

12. Once design has been pressed onto the glass, slowly remove the transfer tape, confirming that the design transfers from the tape to the glass. Repeat with all your remaining glasses.